There are some previous questions with good answers like this one, or this that go into much more detail than I'm about to.
You said your bread didn't rise with the first rise, if you don't have a first rise you can't go onto the next step. If your yeast was old, or the temperature was cold in your kitchen or you used cold water in the dough, or the yeast came in contact with salt then its action could have been slowed down drastically and it would take much longer to get a rise. I've had a first rise take up to 4 hours in the past because of these factors. The times given in recipes are just guidelines, you have to be result-driven. Active dry yeast also takes longer than quick yeast to activate. When using active dry instead of quick yeast you would get better results by mixing it with the water before mixing in. I'd recommend using quick yeast as it's milled into smaller grains and you can mix it directly into the flour.
Of course your yeast may have simply been dead, or killed by salt or heat. Get some good fresh yeast and store it in the fridge to keep it fresh long-term.
Also, using all whole wheat flour isn't going to produce anything like a baguette. Whole wheat flour is very heavy compared to white flour and will take longer to rise. A half and half mix would work better. I'd recommend sticking to the recipe first, then gradually modifying it over time until you get your desired result.
Great question - very well put!
Your chef advice is sound. I have been cooking with cast iron skillets for longer than I care to admit (old guy) and at first they can be intimidating but in the end, they become your go to pan especially for searing/cooking hot.
You asked the same question several times, "is the residue safe?" It's as safe as the cooking oil you use to season it and as clean as you were able to get it before storage. A clean oiled cast iron pan in your cupboard is safe. Sometimes, I will wipe the old residue off with a paper towel just before cooking just to get any dusty nasties off of the cooking surface.
Basically, this is how I use my cast iron.
1) Remove from cupboard
2) Take a look - is there any dirt, debris, dust or corrosion. If so, remove. (Corrosion being the most difficult but a little scouring and re-seasoning will do the trick.)
3) Heat pan thoroughly before cooking - again, the heat will kill anything you can't see but don't want to consume.
4) Cook your food.
5) Eat your food (grin).
6) Clean the pan (NO SOAP)
- a) Remove any remaining food with a scouring brush - in the sink, use hot water and elbow grease.
- b) Fill pan with hot water
- c) Place on burner (on high)
- d) Wait till it comes to boil
- e) Turn off burner and remove from heat (careful - water is hot).
- f) Pour out water and brush clean with scouring pad/brush
- ---If clean, let cool to touch - if not, repeat b-f
- g) When cool, pour a small amount of cooking oil into pan
- h) with a paper towel, spread cooking oil all over the inside of the pan
- i) With the same paper towel, wipe the outside of pan and handles, bottom, everywhere
- --You're looking for a nice coating of oil - no pooling - just a nice gloss. This will prevent corrosion and keep the pan seasoned.
7) Once pan in completely cool, return to cupboard.
Tip - if you were unfortunate enough to leave the braising residue in your pan for a few days and it's a sticky mess, you can try filling it with warm water and putting a couple tablespoons of dish washing crystals (Cascade works best for me) in the pan. These "crystals" contain little enzymes that will "eat" the residue and make cleaning much easier. Don't leave in too long, about an hour or so - repeat if necessary. (Works on other pans too but not recommended for Teflon or non-stick pans.)
Tip 2 - I stack my pans in storage. To prevent metal to metal contact (not good), I put a paper towel between each pan. Be careful that the cast iron is not touching your other pans. Dissimilar metals have a way of talking to each other (causes corrosion on both).
There you have my tried and true method of caring for a cast iron pans. For some reason, I find myself craving some cornbread.
Good Luck!
Gringo Dave
Best Answer
If you read some of the reviews on the one that says to bake for 45 minutes (Brennan's), many of them say it was done in less time:
sunnieday:
Nutmeg~n~Pepper
lambertfan
So it looks like the bake time on Brennan's recipe is too long.
As to the pan vs sheet, with the sides of the pan so close to the loaf, it can certainly absorb and radiate some extra heat to the bread, so that might explain a little of the time difference... but not 30 minutes worth... but since the actual bake time for the sheet loaf is really 25-30 minutes, that might account for it... but the skillet would also take longer to heat up initially (assuming it's not preheated), so it would probably make the bottom of the bread cook more slowly.
So, as always with baking, don't bake by time. Keep an eye on your baking and pull it when it's done, not when the time is up.