Having an issue trying to remove a plastic flange from a 4 inch PVC pipe. I tried cutting and chiseling it away. It must have been cemented with a primer and cement. Are there any other (simple) ways to remove the flange? The top part is off I'm only dealing with the part that is left inside the PVC.
How to remove a plastic flange from a 4 inch PVC pipe
flangetoilet
Related Solutions
I ended up pouring some very liquid mix of waterproof cement down the pipe and catching it again at the exit, it seems that is filled the little cracks inside the pipe. It's been a few weeks of testing by pouring water down and I don't see any leaks anymore. I have to specify that the pipe was horizontal and the cracks on the bottom part of it, that allowed the cement to fill the cracks.
I would recommend replacing all of the affected pipe. The PVC already looks pretty roughed up, and you don't want to invite more problems in by using a rubber gasket fix!
Start by making sure no one is going to flush any toilets, use any sinks, or run any water. Otherwise, things might get messy.
Measure the distance between the 22.5° pipe and the T joint.
Cut the upstream pipe between your T joint and the 22.5° joint. Leave about 1/2 inch of pipe before the 22.5° pipe, and make sure to be careful for the copper pipe running under you!
Now cut your pipe downstream and remove the cut section! Try to make the cut as perfect as you can. If the cut is too cattywompus, you won't get a good seal later and things will get messy. Once you are done, sand the edges so you don't have any rough spots, and then stuff some rags and bags in the hole to keep it from gassing you out.
Get some gloves and paper towels. You will need to clean the outside of the downstream pipe. Clean back about 6 inches. The reason for this is because we are going to put a fresh coupler on it later and need it to be clean, so that it can get a good water tight seal. While you have the cleaning supplies out, you can clean up the subfloor a bit as well :-)
If you have one of those handy dandy pipe driller contraptions that @BMitch talked about, use that to gently drill the upstream pipe that we first cut out of the 22.5° coupler. Image shamelessly stolen. (Thanks @BMitch!)
If you don't have one of those, then you can use a dremel to cut the pipe inside the joint (but not the joint!) and then snap it out. I drew a few pictures showing what I mean...
When you dremel out the pipe, be careful! We don't want to damage the 22.5° joint!
After you are done dremeling, you should have little tabs remaining that you can break off. Then clean out the inside of the joint with some towels and you are ready for step 7!
Remember the distance I had you measure in step 2? Get a 4" PVC pipe and cut it to that length, PLUS the amount it will need to fit inside the 22.5° bend AND the end of the T joint. Cement the newly cut pipe into the T joint using purple primer and then PVC Cement.
Cut another segment of 4" PVC Pipe. This should butt up to the cut we made on our downstream pipe (with a 1/4" gap). Cement this section to the bottom of your T joint (towards sewer).
I have drawn a picture of what steps 7 and 8 should look like. The 4" PVC pipe you are cutting is shown in red. Please check the measurements, mine are just guesses! Notice how there is a 1/4" gap between the sewer line and the pipe we just cut. Get that gap as close to 1/4in as you can!
Once you have gotten this far, you need a 4" PVC Repair coupler. A normal coupler has a "Stop" half way through it, to make sure that the pipes are in the correct distance.
However, a repair coupler does not have a stop in it. Here is where things get tricky...
Get your PVC Coupler, and slide it up several inches so that it is near the bottom of the T joint. See picture. After you slide the coupler on, prime all your pipe ends, as well as the downstream pipe and the upstream joint.
Next, put PVC Cement on all your primed areas. So that would be in your 22.5° joint, on both of the red ends of the pipe in the previous photo, and on the downstream pipe end.
Twist and slide the top of your pipe into the upstream segment of pipe so that it is attached there. Then quickly slide and twist your coupler piece down so that it neatly joins the end of your pipe with the downstream pipe. See pictures:
All done!
Related Topic
- Toilet won’t come off the flange
- Plumbing – What can replace this PVC toilet flange in iron pipe
- Plumbing – Removal of toilet flange in bathroom remodel with subfloor replacement and tile installation
- Plumbing – PVC toilet flange replacement problems
- ABS offset toilet flange dilemma. Suggestions to make the 11“ rough-in into a 12” rough-in. USA
- Plumbing – How to repair a pvc flange set into concrete slab
- Flange recommendation needed. Old flange rusted. New floor higher than older pvc pipe lip
Best Answer
I've seen some discussion here of fancy plumber tools (a bit too expensive for the amount of use anyone but a plumber would put them to, unless you can find them in a rental store) that apply heat and grip/pull things apart.
Other than that (which I've never seen or used, only seen mentioned), I'm prone to consider PVC joints as forever, so the stock approach when you need a new one is to cut at a point where you can install a coupling, some new pipe (in most cases), and the new fitting.