Where should I position a recessed contact sensor in a door

What I have yet to find a solid answer on is what is typically run to the keypads. Do I run cat5/6, or use the same security wire (or both)?

I recommend running 22/4 and cat5e from the security panel to the keypads. That provides lots of options.

Once I run the wires to each window, where do I leave the wire?

I recommend leaving a coil of wire in the window return.

Should I drill a small hole in the rough window frame, and pull the wire through?

Yes. Exactly.

If I do drill a hole, where should the hole be positioned?

Somewhere that meets these criteria:

• a spot that minimizes the run of exposed cable from the window frame to the contact
• in a position that won't interfere with the installation of window coverings
• in a position that lends itself to finishing the window frame area (e.g. avoid spots that will become finished vertices)

I guess I'm questioning the workflow more than anything. For instance, do those putting up the sheetrock, installing windows, or those installing the molding around the window typically know how to deal with these wire?

In general, the other trades will make sure your wire doesn't get buried, but where it ends up and in what condition it will be in is uncertain.

I recommend installing the windows before wiring. If the returns are drywall, I recommend one of the following:

• install your own peice of Sheetrock on the part of the return where the wire is run
• have your contractor board the drywall returns but not the walls or ceilings before you wire

If your returns are wood, I recommend coiling wire on the studs inside the window frames, and working out a specific plan for how the wires will be handled with your carpenter just before he starts work.

I will not be installing the system for months after we move in, so would prefer not to have cables sticking out of the window frame until the install is complete. Do I have any chance of fishing the wire out if I drill a small hole in a window frame?

Not likely. If you are concerned about aesthetics, just finish the contact install for those windows that matter.

Motion Sensors and Keypads

Unlike window contacts, these are mounted to the walls like any other electrical device. I recommend using open-backed electrical boxes rather than just a hole in the sheetrock. There is some more information about them in this question.

Hidden Door Contacts

I recommend this type of door contact for doors that open inward. It fits right in the top of the door frame. The contact itself will need to be installed when you rough-in.

Note, I'm not anywhere near an alarm professional, however I have installed a couple systems before and have just recently been researching again as I prepare to move into a new house where I'd like to install an alarm.

Keypads

You'll want a keypad anywhere you normally enter/exit the house, such as by the garage door or back door. As @bib points out, you may also want one in the master bedroom to be able to use panic, or see status of the system.

Window Contacts

Whether contacts on the windows are worthwhile depends on what you are trying to protect.

• My opinion is it's better and easier to cover the areas with a motion sensor. If someone breaks the window, the alarm still goes off if they come in. If you want to leave a window open (normally you'd have to bypass the zone to arm) you're still covered.
• The caveat to this is for "stay" arming. Typically when you're at home and arming the system, all the interior motion sensors are bypassed. If there is a window that is easily accessible from the ground floor, you may want a contact on it. For the second floor, it's probably not likely that someone is going to manage to get a ladder up to your house without either waking you up or making the neighbours suspicious so it's probably overkill there.

Glass breaks

Glass break sensors are another good way to cover likely intrusion points through windows where someone is going to smash it to get in. Patio doors and sidelights beside doors are good options. The sensor you quoted is actually an older style, most of the new ones are audio sensors that listen for the sound of breaking glass and work in anywhere from a 10 to 25' radius (depends on the glass, check specs). You can get these combined with motion sensors as well.

Glass break sensors are good for "stay" arming (when motion sensors are bypassed) or if you want early warning. In most cases, a motion sensor is going to alarm even if the glass break doesn't.

Motion Sensors

I would probably put motion sensors in:

• top-right corner of family room - covers windows at the back
• somewhere in entry way (a 360-degree ceiling-mounted would work well) - covers anyone moving through the main area of the house and using the basement stairs
• top-right corner of basement - covers the basement windows

Of course you can put more if you want, but you need to think of what you're trying to protect from. If someone breaks in through, eg, the dining room, they are probably going to walk around and set off a motion somewhere. If you do have enough valuables in a room that someone may break in, steal everything from that room and leave, then you may want to put motion or some other sensor in there.

Siren

The siren should go somewhere it can be heard inside and out. Typically it's just installed in the basement near the alarm panel. You may also consider installing in the attic, or outside (you can get them with flashing lights too) so it's audible/visible to neighbours.

Panel protection

I am also a fan of installing protection around the alarm panel. Usually there is a 30-second delay to put in your code, and that may give someone enough time to get to the panel and disable/disconnect it. If the panel is in its own room, put a door contact on that room and otherwise put a motion sensor in there. Either way that zone should be set up as instant -- even if the system is in the delay entry mode, activating either of those zones should instantly alarm the system. Normally interior zones are bypassed while in delay entry.

This is also a consideration for motion sensor placement -- you can set up the motion sensors so if you were to walk into eg, the living room without disarming first, the alarm would go off. You just have to carefully consider placement here, and ensure that you don't set this up somewhere a person would normally walk before disarming.

Door lock sensor

I am considering my own system, and one neat thing I thought of (though apparently I'm not the first) was to put a plunge sensor in the back of the deadbolt channel, so that it can detect if the deadbolt on the door is locked or not. This may not be part of the alarm, but it can at least let you check the door is locked without getting out of bed or after you're already at work (assuming you have internet connectivity on the system). Unfortunately in my house there is a sidelight integrated into the door that prevents me from doing this.

Garage

You should consider how you use the garage. There are several ways to alarm it.

If you're not trying to protect the garage, it's pretty simple, though you may still want contacts on the doors to at least let you see if they're closed or not.

If you're using a wireless system with remotes, you can arm/disarm the system with those allowing you to exit from the alarm. If not, you need to ensure you have enough time to arm the system from a keypad, and get out of and close the garage doors before the system is done its arming countdown. This may mean putting a keypad in the garage, but again it depends on your use.

Fire

You should also put in some smoke/heat detectors. They can be wired into the alarm and thus monitored as well as setting of the siren (usually it does a different noise) in case of fire.

Monitoring

If you're going to have a company monitor the system, you need to ensure there is connectivity. At least this means a telephone line or internet connection. For telephone lines, a special jack (RJ31X) is used that allows the alarm to disconnect and take over the line, and so you need to route the main telephone line to the alarm panel before it goes to any other jacks in the house.

However you should also consider that someone may cut the line, and in that case communications is down. You can get GSM cellular options for communication that work around this.