Why do some light fixtures use multiple bulbs

light-fixture

I've never really given much thought to this until recently. Why would I want to put multiple bulbs into a single fixture?

Every bulbs burns at a specific brightness. Putting more bulbs next to each other won't make the light brighter. Or will it?

So what does it actually do? Obviously, it will spread out light at a larger area, but how much are you actually achieving if the bulbs are so close together as they are with this fixture?

Light fixture for 3 bulbs

The question came up because I'm equipping multiple rooms with LIFX bulbs. When I spend that kind of money, I'd like to know that I'm actually achieving something by putting multiple bulbs right next to each other.

Best Answer

We use artificial light to light up things. The brightness of a thing depends on how many photons are falling on it. Doubling the number of bulbs actually does double the number of photons. That makes the thing visibly brighter.

One basic method of dimming a room is to have 2 switches, each of which controls some lights.

More bulbs will not throw the light any farther. What will happen, however, is that faraway things will get more light with more bulbs. For instance with a single bulb, it might get 5 lux... with 4 bulbs it will get 20 lux and thus be more visible.

Related Solutions

Electrical – How to get the fluorescent light fixtures to work with an occupancy sensor

The basic problem is that the occupancy switch that you chose to purchase is one designed to be able to work in series with the load attached to it. If the attached load is too small (too low of wattage) the switch assembly does not get enough power to operate correctly. For the particular model you have this is on the order of 40 to 50 watts of minimum load. From a technical standpoint it kind of sucks that they work this way BUT they are designed to work in place of a simple light switch that is in in series with its load.

Your Radio Shack relay does not come close to representing a 40-50W load on the switch so the only other way is to add some additional load in series with the switch (i.e. equivalently in parallel with the relay coil). As you have come to see this is not a very satisfactory solution and some other scheme needs to be found.

The best situation in this case is to acquire the alternate type of occupancy switch as mentioned in that thread that you linked. That type of switch has a live AC lead and neutral AC lead connected to it to power the switch unit irrespective of the size of the load. A separate output connection goes off to the load you are trying to switch. This type of switch may take a little re-wiring in your garage but that should be easier than trying to wire in the kludged extra load that the current switch requires. If you choose to deploy this improved version of the switch you will be able to remove the Radio Shack relay from the installation.

To make yourself feel better about the fact that you now have an extra occupancy switch you could pick a room in your house that has a tendency to get its light left on accidentally and install the extra unit in place of its light switch. Maybe this is a bathroom the kids use or a far closet that does not get used often.

BTW

It looks like Leviton now has a whole slew of different model occupancy switches that are also designed for single pole switch replacement but have removed the minimum load requirements. These do not require a neutral wire connection but do require a GND wire connection.

Lighting – Multiple weak light bulbs vs one strong light bulb

Minimum Code Requirement and the Problem with Uneven Lighting

It seems like you're trying to correct for what is likely minimum code requirement wiring. Usually that means a single electrical box for a light fixture in the middle of a room, or a switched outlet ostensibly for floor lamps. The problem with this minimal number of fixtures is twofold:

As you identified, there are entire parts of the room that will be in a shadow because light travels in a straight line. You'll get some reflections off of the walls and other objects in the room, but that will generally be at a loss on the order of 10x.
The intensity of light from a fixture that falls on an object is roughly proportionate to the inverse cube of the distance from the light. This means that an object 9 feet from the fixture has approximately 1/27 the light falling on it as does an object 3 feet from the fixture.

The above two problems can be summarized as uneven lighting. The trouble with uneven lighting is that your eye will adjust to some sort of average of the brightness. The single bright light in the middle of the room is probably way brighter than that average, so it becomes uncomfortably bright to have in your field of vision. At the other extreme, the shadows are likely much dimmer than average, so your eyes will likely just see dark.

Both of the above problems are lessened by increasing the number of light fixtures.

How Many Fixtures Do You Really Need? Experiment!

To achieve even lighting, you need way more fixtures than minimum code requirement. My last renovation included one light fixture for every 25 square feet on average which represents about 5 times the number of fixtures that were originally installed. That's just about what is minimally necessary if you want to avoid both shadows and having bright bulbs within your line of vision.

Of course, the ideal number of fixtures depends on your room shape, light fixture design, wall, ceiling, and floor colors and material, and a bunch of other things. Accordingly, I found that it is best to experiment with your space before electrical rough-in by mocking up the fixtures and trying them out in the location to make sure you're happy with the result. For the experiments to be meaningful, you really need to have multiple fixtures so that you can evaluate how their lighting adds in the room. During renovations, I usually just screw a bunch of fixtures on cords to the original walls and ceiling drywall and see what happens. If you're trying to preserve your finishes, you'll need to get more creative -- I've used tripods and photography light stands before too.